DC-CAR Forum

Alles zum Modellautobau mit dem DC-Car Decoder
Aktuelle Zeit: Freitag 29. März 2024, 05:49

Alle Zeiten sind UTC + 1 Stunde




Ein neues Thema erstellen Auf das Thema antworten  [ 6 Beiträge ] 
Autor Nachricht
 Betreff des Beitrags: Acceleration/Deacceleration DC05
BeitragVerfasst: Mittwoch 13. Januar 2010, 19:39 
Offline

Registriert: Samstag 9. Januar 2010, 18:38
Beiträge: 5
Wohnort: Norway, Oslo
Hello!

I've tried to read the manual for the DC05 decoder, but I'm not able to find any CV for changing acceleration-/deacceleration time. Is it at all possible? If so, how is it done?

Best regards,
Nils :D


Nach oben
 Profil  
 
 Betreff des Beitrags:
BeitragVerfasst: Donnerstag 14. Januar 2010, 09:08 
Offline
Site Admin
Benutzeravatar

Registriert: Mittwoch 23. Juni 2004, 09:04
Beiträge: 562
Wohnort: 70825 Korntal-Münchingen
Nils,

you may change the acceleration-/deacceleration time only for the distance control.
CV48 controls the hardness of the break
CV53 and 54 controls the acceleration

You have to play around with the values !
An often used setup will be:
CV48 = 65
CV53 = 25
CV54 = 50

Claus

_________________
Der Erfinder des DC-Car Decoders !
Ein Experte ist ein Mensch, den man in letzter Minute hinzuzieht, um einen Schuldigen zu haben...
Zur Internetseite http://www.modelleisenbahn-claus.de
Zum Shop http://www.shop.modellautobahnen.de/


Nach oben
 Profil  
 
 Betreff des Beitrags:
BeitragVerfasst: Donnerstag 14. Januar 2010, 19:33 
Offline

Registriert: Donnerstag 2. April 2009, 15:23
Beiträge: 30
Wohnort: DE56 2TZ Belper, England
Yes I have had fun doing this as well!

I found that changing CVs 48,53 and 54 did not necessarily make a lot of difference but found that these changes were more effective (or am I missing something?) if I also changed the speed steps (Fahrstufe) CVs 70-97. Some chips have come with a range from 168 - 41 and others 180 - 45. Also the steps can be varied so that the lower speeds have smaller or larger steps.

I had one vehicle where I had to make the speed steps higher or else the vehicle just crawled along.

But clearly as Claus has said, you need to play with the values.

Ray


Nach oben
 Profil  
 
 Betreff des Beitrags:
BeitragVerfasst: Montag 1. Februar 2010, 17:37 
Offline

Registriert: Samstag 9. Januar 2010, 18:38
Beiträge: 5
Wohnort: Norway, Oslo
Hello
I work with model train normally.
I have tested decoder DC05. And it isn?t easy to control the cars in slow motion.
And I have tested a lot of cv. In result of many funny happenings and accidents.:shock:
In the decoders for train do they have feedback from the motor to hold constant speed.
Will that be possible in a next version? Or have I missed something in the programming.

And I still don?t like the fast stop in front of ir- stop signal. Isn?t possible to fix that in a way?
Even from step 14, do the cars stop to fast. The cv for distance controls works bad on that.
But when controlled manual or by WinDigipet do they run much better from start to stop.

Best regards from Nils
:D


Nach oben
 Profil  
 
 Betreff des Beitrags:
BeitragVerfasst: Dienstag 2. Februar 2010, 09:11 
Offline
Benutzeravatar

Registriert: Mittwoch 20. Dezember 2006, 13:29
Beiträge: 163
Hi Nils

That the cars stops immediately at an ir-stop is not a bug. If the car does not stop that fast, it might pass the coverage area of the led and will accelerate again.
AFAIK there is no load control for the engine implemented at the moment.

Best regards
Achim


Nach oben
 Profil  
 
 Betreff des Beitrags:
BeitragVerfasst: Mittwoch 3. Februar 2010, 10:23 
Offline

Registriert: Donnerstag 2. April 2009, 15:23
Beiträge: 30
Wohnort: DE56 2TZ Belper, England
I must agree that a speed ramp would be a very useful addition such as happens on, dare I say it, the Tams FCS Modules.

Ray


Nach oben
 Profil  
 
Beiträge der letzten Zeit anzeigen:  Sortiere nach  
Ein neues Thema erstellen Auf das Thema antworten  [ 6 Beiträge ] 

Alle Zeiten sind UTC + 1 Stunde


Wer ist online?

Mitglieder in diesem Forum: 0 Mitglieder und 9 Gäste


Sie dürfen keine neuen Themen in diesem Forum erstellen.
Sie dürfen keine Antworten zu Themen in diesem Forum erstellen.
Sie dürfen Ihre Beiträge in diesem Forum nicht ändern.
Sie dürfen Ihre Beiträge in diesem Forum nicht löschen.
Sie dürfen keine Dateianhänge in diesem Forum erstellen.

Suche nach:
Gehe zu:  
Powered by phpBB® Forum Software © phpBB Group
Deutsche Übersetzung durch phpBB.de